Hybrid-pi model

The hybrid-pi model is a popular circuit model used for analyzing the small-signal behavior of transistors. The hybrid-pi models apply only to devices in active mode; that is, the DC biases are applied to set the operating point or Q-point in the normal operating regime for analog circuit operation. The model can be quite accurate for low-frequency operation and can be adapted for higher frequency operation by addition of inter-electrode capacitances and other parasitic elements.

Bipolar transistor

(PD) Image: John R. Brews
Simplified, low-frequency hybrid-pi BJT model.

(PD) Image: John R. Brews
The bipolar hybrid-pi model interpreted as a y-parameter two-port. The emitter node is split artificially to satisfy the port conditions.

The hybrid-pi model is a linearized three-terminal approximation to the transistor using the small-signal base-emitter voltage v_π and collector-emitter voltage v_ce as independent variables, and the small-signal base current i_b and collector current i_c as dependent variables.

A basic, low-frequency hybrid-pi model for the bipolar transistor is shown in the figure. The three transistor terminals are E = emitter, B = base, and C = collector. The base-emitter connection is through a resistor r_π, and the base current causes a small-signal voltage drop across it, v_π (the π notation is standard). Voltage v_π induces a small-signal collector current via the voltage-controlled current source with current g_mv_π, g_m is the transistor transconductance.

This three-terminal model can be viewed as a y-parameter two-port network, as shown in the next figure. However, to satisfy the port condition that, to qualify as a port, current into and out of a selected port both must be the same, a mathematical artifice of splitting of the emitter current into separate base and collector currents is introduced, which does not correspond to any physical phenomenon. If this two-port is inserted into a larger circuit, the input and output port conditions will be violated if the connected circuitry does not itself satisfy the port conditions. To elaborate: this four-terminal model of the bipolar transistor does not enforce the port conditions, it is only compatible with them if they are requested by the surrounding circuitry.

Equivalence to the three-terminal circuit is established using the relations v_π = i_br_π and β = g_mr_π. Thus, the dependent source current g_mv_π = βi_b, and is the same in both circuits.

The various parameters are as follows.

• $g_{m}={\frac {i_{c}}{v_{be}}}{\Bigg |}_{v_{ce}=0}={\begin{matrix}{\frac {I_{\mathrm {C} }}{V_{\mathrm {T} }}}\end{matrix}}$ is the transconductance in siemens, evaluated in a simple model (see Jaeger and Blalock)

where:

• $I_{\mathrm {C} }\,$ is the quiescent collector current (also called the collector bias or DC collector current)
• $V_{\mathrm {T} }={\begin{matrix}{\frac {kT}{q}}\end{matrix}}$ is the thermal voltage, calculated from Boltzmann's constant, the charge on an electron, and the transistor temperature in kelvins. At 290 K (an approximation to room temperature: 70°F ≈ 294 K) V_T is very nearly 25 mV (Google calculator).

• $r_{\pi }={\frac {v_{be}}{i_{b}}}{\Bigg |}_{v_{ce}=0}={\frac {\beta _{0}}{g_{m}}}={\frac {V_{\mathrm {T} }}{I_{\mathrm {B} }}}\,$ in ohms

where:

• $\beta _{0}={\frac {I_{\mathrm {C} }}{I_{\mathrm {B} }}}\,$ is the current gain at low frequencies (commonly called h_FE). Here $I_{B}$ is the Q-point base current. This is a parameter specific to each transistor, and can be found on a datasheet; $\beta$ is a function of the choice of collector current.

• $r_{O}={\frac {v_{ce}}{i_{c}}}{\Bigg |}_{v_{be}=0}={\begin{matrix}{\frac {V_{A}+V_{CE}}{I_{C}}}\end{matrix}}\approx {\begin{matrix}{\frac {V_{A}}{I_{C}}}\end{matrix}}$ is the output resistance due to the Early effect, and V_A is called the Early voltage.

Higher frequencies

(PD) Image: John R. Brews
Bipolar hybrid-pi model with parasitic capacitances to model frequency dependence.

As frequencies are increased, amplifier gain drops off with increasing frequency because the bipolar transistor is degraded by parasitic capacitances. These effects must be modeled to assess the limitations of bipolar circuits. Three parasitic elements are commonly added to the hybrid-pi model to make frequency predictions. One is the base-emitter capacitance C_π, which includes the base-emitter diffusion capacitance and the base-emitter junction capacitance. At high enough frequencies, C_π shorts out the transistor and it fails to function. A second parasitic capacitance C_μ connects the base to the collector. Although this capacitor is small, its influence is multiplied by the transistor gain which amplifies the voltage variation at the base connection and applies it to the collector connection, exaggerating the influence of this capacitor through the Miller effect. The small series base resistance r_x plays a role only when there is no other resistance introduced by the circuit into the base lead. For example, if the base is grounded, the presence of r_X means the top of the base resistance r_π is not at AC ground, and can develop a transient voltage, which in turn can enable gain roll-off due to the Miller effect capacitance.

Related terms

The reciprocal of the output resistance is named the output conductance

• $g_{ce}={\frac {1}{r_{O}}}$.

The reciprocal of g_m is called the intrinsic resistance

• $r_{E}={\frac {1}{g_{m}}}$.

MOSFET

(PD) Image: John R. Brews
Simplified, three-terminal MOSFET hybrid-pi model.

(PD) Image: John R. Brews
Four-terminal small-signal MOSFET circuit.

Unlike the bipolar transistor, the MOSFET fundamentally is a four-terminal, not a three-terminal, device, the terminals being S = source, D = drain, G = gate, and B = body or substrate. The body is not normally used deliberately as a signal node, and the analogy to the bipolar device is stretched a bit to minimize differences between these devices.

The upper figure shows the three-terminal small-signal equivalent circuit for the MOSFET, which ignores the body contact altogether, anticipating it is short-circuited to the source. At low frequencies,the capacitances all are replaced with open circuits to obtain a frequency-independent circuit depending upon resistors only. The various parameters are as follows.

• $g_{m}={\frac {i_{d}}{v_{gs}}}{\Bigg |}_{v_{ds}=0}$

is the transconductance in siemens. The various parameters can be evaluated using a variety of models. For example, with the Shichman-Hodges model, in terms of the quiescent point (that is, zero signal) drain current $I_{D}$, one finds::

$\ g_{m}={\begin{matrix}{\frac {2I_{\mathrm {D} }}{V_{\mathrm {GS} }-V_{\mathrm {th} }}}\end{matrix}}$,

where:

$I_{\mathrm {D} }$ is the quiescent drain current (also called the drain bias or DC drain current)

$V_{th}$ = threshold voltage and $V_{GS}$ = gate-to-source voltage.

The combination:

$\ V_{ov}=(V_{GS}-V_{th})$

often is called the overdrive voltage.

• $r_{O}={\frac {v_{ds}}{i_{d}}}{\Bigg |}_{v_{gs}=0}$ is the output resistance due to channel length modulation, calculated using the Shichman-Hodges model as

$r_{O}={\begin{matrix}{\frac {1/\lambda +V_{DS}}{I_{D}}}\end{matrix}}\approx {\begin{matrix}{\frac {V_{E}L}{I_{D}}}\end{matrix}}$,

using the approximation for the channel length modulation parameter λ

$\lambda ={\begin{matrix}{\frac {1}{V_{E}L}}\end{matrix}}$.

Here V_E is a technology related parameter (about 4 V / μm for the 65 nm technology node) and L is the length of the source-to-drain separation.

The reciprocal of the output resistance is named the drain conductance

• $g_{ds}={\frac {1}{r_{O}}}$.

It must be pointed out that the Shichman-Hodges model for voltage and geometry dependence of the device parameters such as g_m, r_O has absolutely no claim to accuracy, especially in today's technology. However, it still is widely used in textbooks to get the flavor of MOSFET circuit design. Nobody would actually implement a circuit expecting this model to be quantitative, however, and real design work always involves extensive computer modeling, for example, using the BSIM computer model.

The small-signal circuit of the lower figure explicitly introduces the body contact and the capacitances to the body. This circuit is a great deal more complicated than the three-terminal circuit, and is avoided where possible. However, in some circuits the body is not short-circuited to the source, and the body must be explicitly handled. Even at low frequencies the effect of the dependent source g_mbv_bs (the so-called "back gate") must be taken into account.